How To Construct A Storage Bench In 8 Straightforward Steps!

Let’s Construct an Out of doors Storage Bench!

DIY Storage Bench Plans

$9.99

You’ll be able to go lots of other ways for materials for this storage bench however I went with an exterior rated MDF known as Armorite. I do know, I do know, it’s usually a cardinal rule which you could’t use MDF in conditions the place it may get moist, as customary MDF swells and is perpetually ruined. Simply have a look at how a lot that expanded? This Armorite is just not solely moisture resistant however can be handled with zinc borate to withstand rot and termites. plus it machines so clear in comparison with customary MDF, that is straight off with none sanding.

I’ve created a set of construct plans to assist making constructing your out of doors storage bench easy.

Supplies I Used to Construct the Out of doors Storage Bench:

Step 1: Organizing Storage Bench Components and Pre-Drilling

I first organized my elements on one in all my work areas earlier than getting began. To begin the storage bench meeting, I first be part of collectively the entrance to one of many sides. Since this undertaking might be going outdoors, I’m utilizing an exterior wooden glue on all of the joints then pre drilling and operating in a screw. I place my items close to the tip of my workbench in order that I don’t have interference with my drill when pre drilling. After getting the primary facet join, I repeated to attach the opposite.

Step 2: Putting the Backside Between the Storage Bench Partitions

Now earlier than attaching the opposite facet, I’m going to slide within the backside, this could match good between the 2 quick sides. As soon as in place, I run across the three sides and add in screws to connect it. With that achieved, now the ultimate fourth facet of the field could be added in the identical method. Good and straightforward. Needless to say I’m making mine for out of doors however you can also make yours right into a finish of the mattress bench or a keys toy chest, or something the place you want ornamental storage.

Step 3: Including Legs to Get it off the Floor!

The storage bench physique is completed. Lets add some legs to it. All the pieces is made out of Armorite and to differentiate the legs some, I took all of the items to the miter noticed first to chop in a slight angle. Now they are often added to the physique. Two items will make up the leg, one is narrower than the opposite in order that each look the identical width as soon as they’re connected. I’m utilizing wooden glue as soon as once more however now converted to utilizing 1 1/4” brad nails as an alternative of screws. To ensure that the legs to return out wanting the identical width, they must be connected correctly. That means the small facet must be positioned on first.

Effectively whereas I’m fixing my mistake I’d as properly present you a tip to take away brad nails. As a substitute of clipping them, which by no means leaves them completely flush, I like to tug them out on the bottom. I do that with the big set of Crescent’s sq. nostril pliers. I get a superb grip on it then roll the nostril so it pulls the nail up straight. Typically it breaks, however it’s simple to get one other grip and pull it the rest method.

Step 4: Putting the Facet and Adorning the Physique

With the quick facet in place, now I can butt this one proper up flush and the whole lot will come out wanting right. One other method you are able to do it’s by putting the unit on it’s head, yeah really this fashion is far simpler, as you’ve got the workbench as a reference level for each of them as an alternative of holding one up whereas making an attempt to get it flush to the highest.

Lets stand it up and have a look. Sure, good.

Noooow, lets tilt it again down in an effort to enhance the physique. I’m going with a lap siding look. That is very simple to attain. You can begin off with a small strip piece down on the backside, it will create a bump off for the primary siding strip. For the whole lot on this step I’m utilizing just a little little bit of wooden glue and brad nails.

Truly, I’m going to go forward and decrease this to the ground because it’s simply excessive sufficient to be annoying….or possibly I’m simply quick sufficient. This might be a lot simpler to see and use my nail gun at this top however now I simply must seize one in all my rolling round stools. 

Step 5: Attaching the Lengthy Sides

Okay to begin attaching the siding, this goes fast and straightforward. I laid down the primary strip in order that it’s flush with the trim piece beneath. From there, every strip is minimize to slot in between the legs in order that’s simple to get proper however the overlap quantity can differ. To verify all of them come out constant, I minimize a spacer. Now I simply need to line this spacer as much as the underside facet of the earlier strip then nail it in place. I transfer this spacer over to the appropriate and repeat. Then to the middle and repeat.

With it caught in place, I throw in a couple of further ones in between earlier than transferring on to the subsequent and repeat the method once more. Whenever you’re taking pictures in brads, take into account the over lap that every board could have and ensure to position your brads on this zone. That method the subsequent board you lay down will cowl up the nail gap. Oh I don’t know if I discussed earlier than, however the complete physique is made out of 3/4” however the slats I made out of 1/4”. Armorite is available in various sizes, I’ve even used 1” earlier than on tasks.

One thing else to speak about on this step is adhesive. There’s only a nook of the slat making contact to the physique so you may’t use wooden glue. You’ll wish to swap to building adhesive and my go to for tasks is DAP Dyna Grip. It’s rated for inside or exterior and a small bead in a couple of locations beneath every new slat works nice.

Step 6: Attaching the Quick Sides

After I received the lengthy facet full, I flip the unit up on finish and repeated with the quick facet. That’s one other distinction with Armorite it takes brad nails a lot cleaner than customary MDF. You don’t get that mushrooming and chipping.

Now, down we go and lets take a look. Effectively, that’s fairly darn cute. And so fast!

Step 7: Putting the High of the Storage Bench

Lets preserve the momentum going by including the highest. For my lid I went with a airplane slab of MDF as a result of I plan to have cushions on it for sitting. However know you would all the time minimize in a cool patten or make it appear to be particular person boards like I present the right way to do on an outside cupboard. I’ll hyperlink that for you beneath. I line up the highest to the physique in order that it’s flush on the again then pre drill and connect the hinges.

Step 8: Portray the Storage Bench

Labored like a allure. Word that I didn’t add a deal with or minimize one in as a result of there’s a in-built lip that’s simple to seize all alongside the entrance. Let’s break all of those edges and prepare to throw a coat of paint on it! I really did a complete video on the right way to correctly paint MDF so I’ll hyperlink to that beneath in the event you’re . You’ll be able to positively roll or brush on paint, however since I’ve an HVLP, that’s what I used to essentially get in all of the nooks and crannies, simply.

After letting it dry I moved it into place and examined it out. Since I knew I might be sitting my bench up subsequent to the home, I left the lid as is, however an alternative choice is so as to add a series to catch the lid from opening too broad in case you are putting it someplace with no wall. I can sit the cushions in place, however then after I wish to stow them away, I can merely open the lid and put them in till subsequent time.

All in all, this undertaking solely takes about two hours to finish as soon as the elements are minimize. So it’s good and easy however will create an honest quantity of storage for a wide range of totally different areas. Do not forget that I’ve a set of plans and a CNC minimize file in the event you’re fascinated with constructing your personal.