How To Construct A Laundry Drawer In 10 Straightforward Steps!

Let’s Construct a Laundry Drawer!

DIY Laundry Drawer Plans

$9.99

Supplies I Used to Construct the Laundry Drawer

Step 1: Slicing Items for the Drawer

It takes 7 elements to make the physique. So not many. If you need a set laundry drawer plans with dimensions then I’ve that accessible, it additionally comes with a CNC lower file in case you have a CNC. I personally painted my cupboards so I simply used no matter 3/4” sheet materials I had scraps of which is MDF on this case.

I begin by laying the facet items on their again and attaching what would be the backside. When becoming a member of issues collectively, it is going to be the identical course of on the whole lot, I used DAPs weldwood wooden glue then predrill and run in a screw

Step 2: Making ready the Toe Kick Plate and Attaching Laundry Drawer Sides

This ledge right here might be the place the toe kick plate goes in, which is that this board right here. I’m utilizing it as a spacer to ensure the underside is connected sq.. After utilizing it to align the board from the within, I additionally used it as a spacer to information me on the place to pre drill and run in a screw. Double checking that it labored; it did, so I proceed attaching. I used this trick once more once I wanted to run within the middle gap. So long as the board is flush to the entrance, it can point out the place the three/4 materials begins for the pre drill gap.

After attaching the primary facet, I connected the second facet the identical method. Nonetheless for the reason that toe kick now can’t match inside to verify for sq., I simply used a tape. I measured the highest, then made positive the underside matched earlier than driving in my screws to connect it.

Step 3: Attaching the Toe Kick Plate

Subsequent is to connect the toe kick, which ought to line up completely flush to each of the facet items and the entrance and the again. Similar with the again board that can make up the again of the platform as soon as this cupboard is stood up proper. Good, that’s the backside executed so now lets flip this round, however nonetheless go away it on it’s again, and begin engaged on the highest boards. This board right here will be a part of the perimeters out on the again edge whereas additionally giving me a spot to screw it into the wall afterward when putting in it within the area.

When becoming a member of one thing flush like this, I like to maneuver my work piece to the sting of my workbench if doable. This manner my drill has room to go in straight as a substitute of at an angle the place I may blow out a screw.

Step 4: Attaching the Final Board

The final piece to connect here’s a related board because the final however this one joins the entrance fringe of the perimeters. Since I can’t use my workbench to relaxation it towards, what I love to do is use a clamp to behave as a 3rd hand. These squeeze clamps are nice to carry them within the basic space whereas I get one facet at a time completely positioned and connected. This board will give me one thing to screw up right into a countertop later when it will get put in.

Step 5: Including the Again to the Laundry Drawer

Okay, with that connected, now let me spin this round, tilt it up, and similar to that now we have a cupboard. Oh, I forgot the again. Maintain on, that’s a fast add. Lets simply lay this factor again down, however this time laying it on it’s face. I made the again from 1/4” mdf because it doesn’t should be tremendous thick. 1/4” materials will do a terrific job at holding it sq. and conserving it from racking.

You’ll see that my again is in two items. That’s as a result of I’m utilizing scraps and don’t care concerning the again, which might be on the within and by no means seen, has a appear. If it does hassle you although, you possibly can at all times make it from one stable piece

Alrighty, and now that’s a accomplished physique. So for now, lets simply slide this on over to make room for me to usher in the elements to construct out the within drawer that can maintain the baskets.

Step 6: Securing the Match and Attaching the Sides

All of those elements are additionally included on the plans and cutlist however I seize for what would be the backside first. I personally at all times like to ensure it matches inside the physique earlier than attaching issues simply because I’ve been recognized to seize the improper half earlier than however as soon as I made positive it match, I connected the 2 sides which appear like wings. These have dados lower into them for the underside to slide proper into.

This backside might be locked in as soon as the back and front are connected, however I went forward and threw in a couple of screws. I went to the again and connected the specialty designed again. These slots and these predrilled by means of holes are wanted for the beneath mount drawer slides that I’ll be utilizing.

In the event you use my actual dimensions then you cannot solely use the precise hampers that match on this laundry drawer but in addition the precise drawer slides. Nonetheless, know that if you wish to change dimensions then you definately’ll in all probability need to get totally different drawer slides and alter the design of this again half. An alternative choice is to vary the scale to what you need, however then use facet mount drawer slides and never fear concerning the beneath mount ones. Numerous choices.

Step 7: Finishing the Entrance Meeting

Going to the entrance of this meeting, I connect the massive entrance panel. This may appear massive and boring proper now however you’ll see why the dimensions is required. For now, let me go forward and put it contained in the physique to ensure all of it appears to be like good……annnnd it does. It’s so simple as that, now the whole lot right here on out are ending particulars.

Step 8: Making the Laundry Drawer Slide!

I may connect the beneath mount drawer slides to the underside facet of the cupboard. Seems like this right here. Then go to the within of the cupboard and connect the rails with screws. To attach the 2, I may carry the within portion over to the physique, set it on the rails, then push it in till the 2 parts clicked collectively. It’s so satisfying. Then since I’m making mine appear like two doorways and a high drawer, I crawled inside and connected these items to the skin by screwing them in on the within whereas Jacob held them to the correcting spacing.

Conclusion: The Completed Product

It’s kinda onerous to get a very good angle of this cupboard as a result of the area is actually tight however with out the counter high in place you possibly can see the way it works. Two hampers match completely on the drawer so as to pull it out and toss in your garments, then conceal them away once more by pushing it in. Smooth closed after all.

Even with the countertop on, I’ve loads of room to take the baskets out and in or just toss in garments then reshut it. I like the way it appears to be like like three parts. The place because the unit on the left actually is a high drawer and two doorways on the underside.

I’ve a 4 half sequence of movies the place I cowl how you can correctly paint MDF, how you can construct customized cupboards, how you can improve retailer purchased cupboards, and likewise how you can construct a countertop from scrap 2x4s! So principally if you wish to see how I constructed out the complete room you’re taking a look at, then verify the hyperlinks within the description. In the event you can think about it, you possibly can construct it and I hope I’m an inspiration or information that can assist you get began. I’ll see you on my subsequent undertaking.

Extra Issues I Used to Construct This Laundry Drawer