How To Construct A Firewood Holder In 7 Fast Straightforward Steps!

When you’re in search of a spot to retailer your firewood that is also tremendous cool to take a look at, take a look at this firewood holder DIY. Earlier than, I’d simply have my completely different sizes piled up in containers across the fireside, which was actually unattractive. So on a whim I threw these collectively. The three compartments enable me to separate small, from medium, to giant items of wooden. Seize a set of plans and let me present you ways I construct them.

Let’s Construct A Firewood Holder

DIY Firewood Holder Plans

$9.99

I’ve created a set of plans to make constructing this firewood holder fast and simple!

Supplies I Used on this Construct:

Step 1: Choosing Materials and Reducing to Dimension

I did design and construct these on a whim so when choosing materials, I simply appeared round my store to see what I had already that will match the sizes. I discovered this stack of three/4” reduce off from some cabinets I tore a component that I’ll make the physique from. Then for the again, I’ve some 1/2” plywood from who is aware of what.

I began off by ripping the sheets right down to width wanted. In order for you actual dimensions, I’ve a set of plans obtainable over on my web site. I tilted the blade over to then reduce within the angles wanted to created the pointed miters. Since there are loads of repeated components, I arrange a cease block in order that I may make all of them the identical. Whenever you do that, you wish to be certain that to set the cease block again far sufficient so the board gained’t be touching it when it contacts the blade. As that is what may cause chill.

To save lots of from switching the blade forwards and backwards, after reducing one aspect with the wanted angle, I’d flip the board and reduce the opposite aspect because it nonetheless had a 90 on one finish. This can depart the remaining board with angles on each finish, that I can chop up for the mitered components. I personally wish to all the time do a take a look at first and a dry match to ensure issues are going to work as I’ve them deliberate. That appears good although.

Step 2: Banding the Edges of the Firewood Holder

Now I simply wanted 12 of them complete so I locked within the new distance for the fence for this half and chopped up the remaining bit into items.

This undertaking solely consist of 4 completely different components. What I’ll name the aspect, the tops that are barely longer than anything, the horizontal cabinets, then the mitered factors. Remember the fact that it could be easy so as to add extra to subtract the variety of cubbies, relying in your areas wants.

Alrighty, now I’ll edge band the perimeters that will likely be dealing with the entrance. Truly, on second thought, I like the concept of portray them as a substitute. Be aware: that should you edge band you’ll want to try this earlier than becoming a member of the components collectively, however if you wish to paint, then you may go straight into assembling.

Step 3: Assembling the Firewood Holder Cubicles

For assembling, I began off on prime of my workbench and what I did is apply some wooden glue, I’m utilizing DAPs weldwood right here, to each joint, then pin nailed issues collectively utilizing my 23 gauge nailer. This can be a fairly weak joint till the wooden glue has time to arrange, so I used to be being cautious as I used to be transferring it round to connect the following leg. If I didn’t have a 23 gauge, I’d have used a 18 gauge as a substitute.

After getting a number of connected, I believed it could make issues simpler to do it on the bottom so I may see every part clearly as I used to be attaching legs. So I moved it right down to the ground and continued. I’d juke and jive to create the factors of the cubbies, then connect the horizontal that may create the separation between.

I paused after I acquired to the very prime as a result of the way in which I’ve it designed, the highest edge will truly be seen. With that, I edge banded each of those components earlier than including them on. This is so simple as heating up an iron and warming up the glue on the again of the banding till it sticks to the plywood edge. This will likely be barely completely different than the ply, however it doesn’t hassle me.

Step 4: Portray the Firewood Holder Cubbies

 I left that the place it sat to provide that glue time to arrange and dry. Whereas it was, I grabbed items that may make up the again from my 1/2” plywood scraps. I additionally grabbed the items that may make up the edges. I would like each of those to be painted the identical colour as my wall which implies I want to provide them a number of coats earlier than attaching the cubbies.

Since I’ve the paint out, I additionally needed to color that entrance fringe of the cubbies. I first give them each a very good sanding to get them clean. Now when working with plywood, there are sometimes voids on each single edge. In an effort to get a clean wanting paint floor, I apply some wooden filler on a putty knife. I’m utilizing DAP Premium wooden filler. These things not solely dries quick however is simple to sand and is nice to paint match in case you are staining one thing.

After letting it dry for about 30 minutes, I got here again with a sanding sponge to knock it down flat in order that I may roll on the paint onto the items of the firewood holder.

With ending out of the way in which, let me simply push this button right here to boost my ending shelf up and find the {hardware} I’ll want to connect the cubbies to the again.

Step 5: Shaping the Again to Match the Firewood Holder Cubbies

I began with a again barely bigger than what I wanted, then plopped the cubbies down onto it and lined it up in order that the underside cubby was flush to the tip of the plywood. I used my pin nailer to only tack issues in place to begin. The top is simple correctly flush, however to ensure the remainder weren’t crocked, I pulled a tape to get the spacing good earlier than tacking the remainder. With it not capable of fall off now, I tilted your complete unit on it’s face in order that I’d have entry to the underside to throw in screws. Right here, I made positive to pre drill to forestall splitting.

Step 6: Securing the Firewood Holder Cubbies to the Again

The highest location is simple to find as a result of you’ve gotten a visible on the place the shelf is positioned. Nevertheless, the second is hard as a result of it’s in the course of nowhere. What I do is seize a pace sq., this Crescent one has a further 6” flip out rule in order that I can place it within the middle of the shelf, go right down to the dimension wanted, and pre drill. When you don’t have this pace sq. or one other lengthy one, then a degree would additionally do the trick.

For the angled portion of the cabinets, the pace sq. wouldn’t work, so I grabbed a scrap and reduce in an angle on the tip. This fashion I may relaxation it on the shelf and permit me to mark the peak. Ensuring to maintain it in the identical location, I moved the scrap to the face closest to me to now drop it down again to the road I made which supplies me the situation of the angled shelf to pre drill and fasten a screw.

With the again on, this factor now feels actually safe and robust. I flipped it up to have a look. I truly assume it appears fairly good with a sq. again on it and was contemplating leaving it as is however then I made a decision to stay to my authentic plan and make the again flush to the geometric form. I wasn’t capable of find my palm router, which is definitely the perfect device to trim the again off, so as a substitute I put a flush trim bit in my router desk and trim it off that means. The important thing right here is to maintain the unit good and flush on the desk as you progress it alongside.

I laid the unit over and connected the aspect. This can assist assist the horizontal cabinets that may truly be supporting the load of the firewood.

Step 7 : Putting in the Firewood Holder and Reducing Firewood

 Very last thing to do was set up them. Now I personally needed mine up off the bottom so I wouldn’t block an outlet I’ve over on the correct hand aspect. Then I additionally like to make use of this space for storing my video games and puzzles. With that, I propped the models up, discovered the studs, then drove a number of screws into the again of the unit to connect them.

Okay lets load it down and see how a lot it will probably maintain. Now that, is significantly better than earlier than. As a substitute of ugly packing containers and totes, I now have a pleasant firewood holder with devoted house for the wooden. This can enable me room to retailer and separate all completely different sizes of firewood throughout winter. Then I personally just like the look of wooden sufficient to maintain it full yr spherical, however I may additionally retailer different kinds of nicknacks throughout spring and summer time ought to I wish to.

What do y’all take into consideration them? Keep in mind how simple it’s to make bigger or smaller. I even assume they might look good horizontal, relying in your house. I’ve a set of plans for this undertaking in addition to many different over on my web site. In reality, if you need firewood storage concepts, I’ve a number of of them.

I’ll see you subsequent time.

Materials I Used For This Construct: