Constructing My Stroll-In Closet Island, Half 2

On the finish of that put up, I hadn’t gotten very far on the island. It regarded like this…

It was form of exhausting to inform that it was an island at that time. However on the finish of the day yesterday, it regarded an entire lot extra like an island. That is what it appears to be like like now…

So let me present you the steps it took to get from that very primary kind that I left off with final time to what it appears to be like like now.

First, I needed to lower and fasten a bit of plywood to separate one of many sections right into a back and front part. Since one part can have drawers on the back and front, it doesn’t want a separator. However the different part can have drawers on one facet and cupboard doorways on the opposite facet, in order that cupboard facet wants a again. To connect that separator piece of plywood, I measured and marked a vertical line in the course of the middle plywood piece…

After which I measured and marked that very same line on the skin piece of plywood. And I used these strains to line up the separator piece of plywood and nail it into place. I simply nailed proper via the skin of the plywood and into the sting of the separator piece. I used small 18-gauge nails, so these holes will likely be very simple to cover with wooden filler.

And right here’s what that regarded like with that piece in place.

Subsequent, I wanted to cowl the perimeters of a lot of the plywood since these would present, and the perimeters of plywood aren’t very fairly.

I coated these edges utilizing pre-glued iron-on wooden veneer…

This edge banding goes on with an iron set to a excessive warmth setting. The iron melts the glue, and when it cools, the banding is adhered to the sting of the plywood. The sting banding is at all times a little bit bit too extensive, so I used a brand new, sharp blade in my utility knife to trim the surplus, after which sanded the perimeters easy utilizing 120-grit sandpaper. And that is what the completed edges regarded like…

I put the sting banding on the entire edges proven in pink under, after which repeated that course of on the opposite facet of the island.

If you happen to’ll keep in mind, the underside fringe of my island truly has a layer of plywood after which a body of 1x3s. Right here’s a reminder of what that appears like from the earlier put up. That is the view of the underside of the island with it flipped over on its facet. See that 1×3 body connected to the underside?

I’m displaying you that to say that I didn’t put edge banding on the perimeters of these 1x3s. I solely put the sting banding on the perimeters of the plywood. Not solely does strong lumber not want edge banding, however I used to be additionally going to cowl the perimeters of that lumber with trim. So once more, the sting banding solely went on the perimeters of the plywood.

Earlier than I might add trim, I wanted so as to add some depth across the backside, so I used my desk noticed and ripped some 1×3’s into strips which are 3/4″ x 3/4″, after which I connected that every one the best way across the backside to the sting of that 1×3 body.

Right here’s a greater view of what that regarded like. You may see the plywood with the sting banding on high, after which the three/4″ strip under connected to the sting of that 1×3 body across the backside of the island. …

With that in place, I began trimming out the tip of the island. I began by connected 1×2’s on the left and the best, however I prolonged these 3/4″ previous the sting of every facet. After which I connected the underside horizontal piece of 1×2.

Earlier than I might connect the highest horizontal 1×2 to finish that body, I connected the sting trim to the countertop (which I forgot to take a photograph of) to see how far down that high body piece wanted to return. Because the edge trim of the countertop overhangs the sting of the island only a bit, that implies that had I put that high horizontal facet body piece on proper on the high of the plywood, the body would have regarded off only a bit as a result of the sting trim on the countertop would have lower off the view of that piece. So I ended up dropping that high horizontal body piece down about 1/2″ from the highest of the facet plywood piece in order that the entire thing could be seen.

Right here’s a view of the facet body items displaying the way it extends previous the sting of the plywood 3/4″. The aim of this, in addition to that backside horizontal piece connected on the backside, is to create an inset for the drawer fronts.

Right here’s what that appears like straight on…

Then I connected the identical trim that I had used across the fringe of the countertop to that backside strip going across the backside of the island.

And contained in the 1×2 body, I used base cap molding to complete off the tip design.

So that is what the tip of the island, the view from the doorway, appears to be like like.

And you’ll see that backside trim continues all the best way round, nailed to the entrance of that backside piece that I nailed on, with each items being flush with one another on the highest.

Right here’s a view from the opposite facet. So hopefully, you’ll be able to think about that the drawer fronts will sit contained in the body created with these items extending on the edges and the underside.

And right here’s a more in-depth view of the trim that I connected across the edges of the countertop.

One drawback that I observed virtually immediately is that I miscalculated the position of the toes. Now that I’ve added all of that trim across the backside, the toes are inset too far in order that they’re virtually not even seen. So I’ll have to flip the island over and transfer the toes out. It’ll look a lot better and extra balanced as soon as I try this.

However that’s the progress! I’m fairly enthusiastic about the way it’s shaping up. Hopefully I could make lots of headway on the drawers, drawer fronts, and doorways this weekend, and have an almost-finished closet island by Monday!